SHIFTER – SHORT MOTORCYCLE LEATHER RIDING GLOVES

Made from thick, full-grain goatskin leather, the Shifter balances durability with all-day comfort. It’s naturally water-resistant and highly abrasion-resistant. The gloves pack CE Level 2 knuckle protectors, Knox SPS 404 full-wrap palm sliders, EVA-padded finger guards, and a SuperGrip silicone panel for added control at the bars.

The Shifter is built to keep your hands safe when it counts. CE Level 2 knuckle armour, full-wrap Knox SPS 404 sliders, TPR protectors with EVA padding, and a leather pinky overlay offer all-round protection. The dual-compound construction of the palm slider helps prevent scaphoid injuries, while goatskin leather ensures reliable slide resistance without compromising on feel.

Dual foam layers under the knuckles and back of the hand reduce fatigue on long rides. Floating knuckles and a stretch panel underneath let your fingers move naturally when operating the levers. Large accordion panels on all fingers and thumbs, plus a pre-curved design, ensure zero bunching and unrestricted comfort all day long.

Step 1 – Measure Your Hand
Grab a tailor’s measuring tape and take two quick measurements:
Circumference – Wrap the tape around the widest part of your palm. Lightly close your hand before noting the number.
Length – Measure from the tip of your middle finger to the base of your palm (where your wrist starts).

Step 2 – Check the Size Chart
Match your measurements with the size chart to find the right fit.
If your length and circumference fall in different size categories, go with the larger one.
If you're in between sizes, try both and pick the one that feels better on the bike.
A good fit means better control, less fatigue, and max protection—don’t guess it.

STEP 1 - Confirm that the gloves are a comfortable fit.
They should not be excessively tight on all fingers (including the thumb) & knuckles.
To check this, try the gloves on and form a fist several times and verify if:
1. Adequate room for all fingers (specially thumb) to move and operate controls comfortably.
2. Check the fitment on both hands since your left and right hand sizes do vary.
Ensure that the fit on first try is not so tight as to cause discomfort and/or restrict movement

STEP 2 - Ensure the knuckle protectors are properly positioned.
The way to check this is:
1. Roll your hand into a tight fist and hold the position for 5-10 minutes. This position should be easy to hold without causing any discomfort or causing any stress points.
2. Ensure that the edge of the knuckle protector is not over the knuckle when the fist is formed."

Cleaning Your Gloves
What you’ll need:
Microfiber cloth, soft-bristled brush, absorbent towel, pH-neutral leather cleaner, leather conditioner, lukewarm water
Steps:
Mix a bit of leather cleaner with lukewarm water.
Dip the microfiber cloth, wring it slightly, and gently wipe the gloves clean.
Mud splatters? Let them dry first, then brush them off before wiping.
Work from wrist to fingertips, getting between each finger.
Rinse your cloth often so you’re not rubbing dirt back in.
Flip and repeat on the other side.
Important:
No hot water.
No harsh cleaners, fuel, fabric softener, or scrubbing.
No machines or pressure washers.
Don’t wring them.

Drying Wet Gloves
Gently press with an absorbent towel—do this even if it’s just rainwater.
Let them dry naturally, indoors, away from sunlight and heat.
Never use a dryer, radiator, or direct sunlight.
While drying, wear them occasionally to keep the shape.

Conditioning the Leather
Once dry, condition them. This keeps the leather flexible, breathable, and crack-free.
Use a good leather conditioner - nothing that clogs the pores.
Rub it in evenly and let it soak.
Wipe off any extra conditioner.

Storing Your Gloves
Only store when completely dry.
Use a breathable cotton bag with a few packs of silica gel - skip plastic.
Keep them in a cool, ventilated place.
Take care of them, and they’ll take care of you on every ride.

1. The Knox SPS palm sliders may feel a bit stiff at first - this is normal for high-protection gear.
2. Give it some ride time - they’ll break in and feel natural soon enough.
3. Always check that the knuckle protectors align well when you make a fist.
4. Avoid folding or crushing the gloves during storage to maintain fit and protection performance.

Product name: SHIFTER – SHORT LEATHER RIDING GLOVES
Name of the commodity: Motorcycle Apparel
Manufactured/Imported By: ViaTerra Travel Gear Pvt Ltd,
OS-2, Opp H-18, MIDC Satpur, Nashik 422007
Country of Origin: Indonesia
Price, wherever mentioned, is MRP and inclusive of all taxes

For customer complaints and support, email or call us
Customer Care Contact : 88866 51324
Email ID: help@viaterra.in