VIATERRA HOLESHOT – SHORT MOTORCYCLE RIDING GLOVES FOR MEN

STEP 1 - Measure your hand using a tailor's measuring tape

There are two key measurements that you need to take into consideration for figuring out your glove size.

1. Circumference - Wrap the tape measure around your palm at its widest point and lightly close your hand before taking the measurement.
2. Length - Measure from the tip of the middle finger to the base of your palm at your wrist.

STEP 2 - Find your glove size by checking hand measurements against the chart provided

• If both the measurements do not fall in one particular size - use the larger of the two measures to choose the glove size.
• If the two measurements are on the border line between two sizes, try both the sizes and choose the one that offers a better fit.

STEP 1 - Confirm that the gloves are a comfortable fit. They should not be excessively tight on any finger (especially the thumb) & knuckles. To check this, try the gloves on and form a fist several times and verify if:

• Adequate room for all fingers (specially thumb) to move and operate controls comfortably.
• Check the fitment on both hands since your left and right hand sizes do vary.

While leather gloves do take some time to break in, ensure that the fit on first try is not so tight as to cause discomfort and/or restrict movement.

STEP 2 - Ensure the knuckle protectors are properly positioned. The way to check this is:

• Roll your hand into a tight fist and hold the position for 5-10 minutes. This position should be easy to hold without causing any discomfort or causing any stress points.
• Ensure that the edge of the knuckle protector is not over the knuckle when the fist is formed.

A few things to keep in mind when you start using the Holeshot mesh motorcycle riding gloves -  

• Putting on and taking off may be slightly difficult, because the wrist area is narrowed down for safety reasons. This is done to prevent the gloves from coming off your hands during a crash and to offer a snug fit.
• You may find the Knox SPS on the palm to be uncomfortable in the first try. But just like any protective gear, over a period of time you will get used to it so you do not even notice it. These devices are incorporated in the gloves is to ensure you are well protected when you most need it.
• In our research, we found that the palm size and the finger length are not in the same proportion for everyone (that makes each of us unique in the truest sense!). In such cases, primary area of fitment should always be the palm area, even if you are to be left with some extra room near your fingertips.
• We have used high density TPU to maximise protection and longevity. While we have added an additional foam layer underneath the TPU, they may feel a bit too hard at the beginning. Thinner and more flexible knuckle protectors are not very effective during a crash and do not last long either.

RISK FREE RETURNS

Concerned that you might not like what you get? While we are extremely confident that you will be more than satisfied with our gloves, we understand that sometimes you might be looking for something different. Not to worry, we offer a zero risk trial within 3 days from the date of delivery. And no, you don't need to pay for the return shipping. Please write to us on info@viaterragear.com if you have any further queries or need clarifications.

FREE SIZE EXCHANGE

Worried about the wrong size if you buy online? You can exchange for size within 3 days from the date of delivery at ZERO cost – yup, we will get the gloves picked up from your address and send a replacement once we receive them in an unused condition. Please write to us on info@viaterragear.com if you have any further queries or need clarifications.

Durable Material:

The HOLESHOT uses goat skin leather that is durable, light and naturally water resistant. The thickness of the leather is kept high for enhanced abrasion resistance.

CE Level 1 Protection:

We chose the low profile KNOX SPS 303 to provide protection without interference during everyday use. For the right fit and better coverage, the knuckle protectors are configured in 2 sizes to work well for small & large hands. The fingers on the gloves have memory foam padding along with PVC protectors for impact protection.

Holeshot surpasses Level 2 standards for the knuckle, palm and wrist to ensure maximum safety on your daily commutes!

• Palm Abrasion Protection as measured by mean abrasion time on palm area - 3.5X Level 2 standard
• Knuckle Impact Protection as measured by mean transmitted peak force on the knuckles - 3X Level 2 standard
• Wrist Closure Resistance measured as force held for 30 seconds - Meets Level 2 standard

Excellent Ventilation & Breathability:

Heavy duty 3D air mesh and perforated leather used throughout to allow maximum air flow - perfect for hot, humid Indian weather!

Enhanced Comfort:

We have also included accordion on the fingers for additional stretch & comfort when operating the clutch and brake. An additional memory foam layer is placed under the knuckle protector with enhanced coverage for added comfort.

CARE:

Our gloves use full-grain goat leather that is naturally water-resistant. However, when leather gets wet, the oils get stripped from the leather – this will stiffen the leather and eventually cause it to crack. Think of it as your skin after taking a bath – you need to moisturize to replace the natural oils in your skin removed by the water. So, what matters for your gloves is what you do after it gets wet. Here is a step by step process to keep your glove well cared for and last longer.

Materials needed:

• Microfiber/ soft cloth
• Small bowl or mixing cup
• Absorbent towels
• Soft-bristled brush
• pH neutral leather cleaner
• Leather conditioner
• Lukewarm water

How to clean riding gloves?

1. In a small bowl or measuring cup, mix a portion of leather cleaner in lukewarm water.

2. Dampen a microfiber cloth with the mixture and gently wipe the stained areas. If the gloves have mud splatters, allow the mud to dry before attempting to clean it away. Use a soft-bristled brush to brush it away before cleaning with cloth.

3. Clean the gloves starting at the wrist and working toward each fingertip. Be sure to clean well between each finger. Keep moving to a clean area of the cloth as the dirt is transferred. 4. Rinse the cloth often as the dirt is transferred. Turn the gloves over and repeat on the other side.

4. DO NOT USE HOT WATER

5. DO NOT allow your gloves to come in contact with solvents (do not use fabric softener!), fuel, or cleaning agents.

6. DO NOT use any kind of CHEMICAL or scrub the leather

7. Do not use a washing machine or high-pressure devices to clean the gloves, as high temperatures and pressure will damage the leather.

How to dry wet gloves?

1. Dry the gloves by pressing softly with an absorbent towel after cleaning. You can also do this when your gloves get wet in the rain.

2. Allow damp gloves to dry slowly, as this will prevent the leather from stiffening and cracking.

3. Never dry wet gloves with a blow-dryer or put them on a radiator or direct sunlight or other heat source to dry – this will harden the leather and lead to damage. Also dry the gloves indoors away from direct sunlight where there is good ventilation.

4. While your gloves are drying, periodically put them on your hands to stretch the leather and ensure they don't shrink.

5. Just before the gloves are completely dry, put the gloves on and shape them to your hand while still damp. Remove the gloves gently, trying to retain this shape in the gloves and allow it to continue drying.

How to condition gloves?

After the gloves are completely dry, apply a good quality leather conditioner. This is very important. Properly treated and conditioned (oiled) leather will breathe and the internal microfibers will move freely in the leather.

1. Use a good quality leather conditioner that will allow the leather to breathe.

2. Apply conditioner and rub it into the leather.

3. Allow the conditioner to soak into the gloves and reapply (if needed).

4. Wipe off any excess conditioner and make sure the gloves are not slick on the motorcycle controls.

How to store riding gloves?

When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.

1. Make sure that your gloves are completely dry before you store them.

2. Place them in a breathable cotton bag to protect them from dust but with enough air circulation to prevent mildew from forming.

3. Store them in a cool, dry, well ventilated area

WARRANTY

We offer a 12 month warranty on manufacturing and material defects. Our gloves are made in the same factories that manufacture for top brands like Dainese, Alpinestars, Furygan, RevIt, etc. Please click Warranty policy for details.

REPAIRS

Minor repairs of opened stitches, velcro etc due to normal wear and tear can be done at a reasonable charge. Send us an email with pictures so we can determine if the gloves can be repaired or not. Please click Repair policy for details.

At ViaTerra, we recognize that accidents can happen on the road, leading to the loss or damage of a single glove. For selected gloves, we are offering an Individual Glove Replacement Service (paid) to assist riders in such situations.

How It Works: If you've lost or damaged one glove and would rather not purchase a new pair, contact our customer service team. While availability cannot be guaranteed, we endeavor to help riders find a matching glove. Occasionally, we have single gloves in a pair that don't meet our QC requirements. We figured that this would be cost effective to our existing customers, by replacing only what you need, rather than buying a complete new pair. We're happy to reunite mismatched gloves instead of discarding pairs with a single damaged glove. Contact us to ensure you're fully equipped for your journeys!