HOLESHOT – Riding Gloves
Safety is paramount even during your daily commute. Keeping this in mind we have designed the Holeshot to offer comfort along with protection even during your day-to-day commute. Holeshot offers high airflow through the 3D air mesh panel on the back of your hand and between the fingers yet provides maximum protection by incorporating perforated goatskin leather on the palm. In addition, we have integrated KNOX SPS sliders as well on the palm to prevent Scaphoid injuries caused by the grab effect when the palm comes in contact with the road in case of a fall.
Get an alert when the product is in stock:
- Detailed Walkthrough
- How to check fitment
- Size Chart
- Things to remember
- Care instructions
- Reviews (30)
- Questions & Answers (12)
How to check fitment
Ensure the knuckle protectors are properly positioned. The way to check this is:
1. Roll your hand into a tight fist and hold the position for 5-10 minutes. This position should be easy to hold without causing any discomfort or causing any stress points.
2. Ensure that the edge of the knuckle protector is not over the knuckle when the fist is formed.
Confirm that the gloves are a comfortable fit. They should not be excessively tight on all fingers (including the thumb) & knuckles. When you try the gloves on, form a fist several times to ensure the below:
1. Adequate room for all fingers (specially thumb) to move and operate controls comfortably.
2. Check the fitment on both hands since your left and right hand sizes do vary.
While leather gloves do take some time to break in, ensure that the fit on first try is not so tight as to cause discomfort and/or restrict movement
Things to remember
- Putting on and taking off may be slightly difficult, because the wrist area is narrowed down for safety reasons. This is done to prevent the gloves from coming off your hands during a crash and to offer a snug fit.
- If you have never used gloves with a pinky bridge you may find it odd or uncomfortable. Give it a few days of riding and you will get used to it. Remember, any protective gear is relatively uncomfortable to wear compared to riding without any protection.
- You may find the Knox SPS on the palm to be uncomfortable in the first try. But just like any protective gear, over a period of time you will get used to it so you do not even notice it. These devices are incorporated in the gloves is to ensure you are well protected when you most need it.
- In our research, we found that the palm size and the finger length are not in the same proportion for everyone (that makes each of us unique in the truest sense!). In such cases, primary area of fitment should always be the palm area, even if you are to be left with some extra room near your fingertips.
- We have used high density TPU to maximise protection and longevity. While we have added an additional foam layer underneath the TPU, they may feel a bit too hard at the beginning. Thinner and more flexible knuckle protectors are not very effective during a crash and do not last long either.
Our gloves use full-grain goat leather that is naturally water-resistant. This means that the gloves do not get ruined if they get wet in rains. However, when leather gets wet, the oils get stripped from the leather – this will stiffen the leather and eventually cause it to crack. Think of it as your skin after taking a bath – you need to moisturize to replace the natural oils in your skin removed by the water. So, what matters for your gloves is what you do after it gets wet. Here is a step by step process to keep your glove well cared for and last longer.
- If your gloves get wet, dry the gloves by pressing softly with an absorbent towel.
- If there are stains, clean the gloves by hand with a pH neutral leather cleaner using a damp cloth or a soft-bristled brush. DO NOT USE HOT WATER
- DO NOT allow your gloves to come in contact with solvents (do not use fabric softener!), fuel, or cleaning agents. DO NOT use any kind of CHEMICAL or ALCOHOL-BASED product.
- Do not use a washing machine or high-pressure devices to clean the gloves, as high temperatures and pressure will damage the leather.
- Do not place your gloves near, or let your gloves get into contact with a direct heat source – this will harden the leather and lead to damage. Also dry the gloves indoors away from direct sunlight where there is good ventilation.
- Just before the gloves are completely dry, put the gloves on and shape them to your hand while still damp. Remove the gloves gently, trying to retain this shape in the gloves and allow it to continue drying.
- After the gloves are completely dry, apply a good quality leather conditioner. This is very important. Properly treated and conditioned (oiled) leather will breathe and the internal microfibers will move freely in the leather. Use a good quality leather conditioner that will allow the leather to breathe. Apply conditioner generously and rub it into the leather. Allow the conditioner to soak into the gloves and reapply (you can do this in the sun). Wipe off any excess conditioner and make sure the gloves are not slick on the motorcycle controls.
- Make sure that your gloves are completely dry before you store them. When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.
Questions and answers of the customers
do you accept for size Exchange
- Qdo you accept for size ExchangeAsked by July 28, 2022 2:51 PMonA Yes, We do. Kindly check our size exchange policy for the details. https://viaterragear.com/policie... Read moreBelow at which temperature in approx these gloves fails to protect our hands from keeping warm ?
- QBelow at which temperature in approx these gloves fails to protect our hands from keeping warm ?Asked by May 3, 2022 11:34 PMonA As these gloves are specially designed for maximum airflow, it will not be a product to wear for wi... Read moreWhich protection level is used in this gloves
- QWhich protection level is used in this glovesAsked by April 4, 2022 10:59 AMonA The Gloves are CE LVL 1 certified.Is the inner side of gloves fiber/(any soft fabric) coated or the same leather (without any liner) ...
- QIs the inner side of gloves fiber/(any soft fabric) coated or the same leather (without any liner) ?Asked by September 13, 2021 8:36 PMonA Yes, we do have soft inner fabric under the leather layer part.When will the gloves of size 2XL be available? Any tentative date will be helpful :)
- QWhen will the gloves of size 2XL be available? Any tentative date will be helpful :)Asked by July 27, 2021 12:21 PMonA Sorry to keep you waiting. The Holeshot 2XL is expected to be back in stock by September 2021. You ... Read more